ProTek35 HD CineWhoop w/ Caddx Polar Vista Digital HD System - BNF (DJI) (6S 2300kv)

Description
Review
Custom Product Tab

After our very popular 3inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.

Our all new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here...

ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all new 2203.5 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to it's 3inch predecessor which gives a lot more room for a lot more fun. Our GPS measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch outs or light freestyle moves.

A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization).

Durable plastic protectors with copper standoffs, portable compact design, easy accessable UBS port without disassembly, LED battery status, lost model buzzer and a universal GoPro TPU for a full size or naked GoPro. If you wanna go extra light, get one of our 5V balance plug GoPro power cables to get rid of the internal battery.

Features:

- ProTek35 Prop Guards V2.0

- No Props or frame in view!

- High performance True-AIO Board Beast Whoop F7 AIO 45A v1.1 to save weight and space

- T700 Quality Carbon (40% more tensile strength compared to common 3K carbon)

- Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable)

- Low Resonance frame construction (Less Jello, more Cinematic footage)

- Caddx Polar Vista Digital HD System

- Butter smooth 2205 2300KV (6S)

- Pre-tuned with smooth freestyle settings

PRE-TUNED & PRE-SETUP:

Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

ProTek35 BNF Specs:

*Board Beast Whoop F7 AIO 45A V1.1

*Motor: XING 2205 2300KV (6S)

*Wheelbase: 151mm

*Body Size: 118*94.5mmmm

*Bottom plate thickness: 3.5mm

*Top plate thickness: 2mm

*Top and bottom plate spacing: 20mm (aluminum standoff height)

*Propeller size: 3.5 inch

*FC pattern: 25.5*25.5mm / 20*20mmmm

*FPV cam spacing: 20mm

*Weight: 348.3g (without battery)

ProTek35 HD Quad BNF Included Components and Parts

Pre-built and tested Quadcopter

1 x ProTek35 Frame

1 x Caddx Polar Vista Digital HD System Kit

2 x Albatross LHCP RP-SMA 5.8g antenna

1 x TPU Bracket for Nebula Nano Air Unit

1 x TPU Antenna holder

2 x Nazgul 3535 propeller (Set of 4 - Color May Vary)

1 x iFlight Lipo Strap 15*150mm (Color May Vary)

1 x iFlight Lipo Strap 15*250mm (Color May Vary)

1 x GoPro TPU bottom stand black (GoPro Protector not included)

FC // Beast F7 AIO 45A V1.1

MCU: BGA-STM32F745

Gyro: MPU6000

UARTs: 5

Blackbox: 16Mb Onboard Flash

BEC output: 5V 2.5A

Barometer: DPS310 (Only Betaflight 4.3.0 and above)

Connector: Micro-USB

OSD: AT7456E

FC Firmware：IFLIGHT_F745_AIO

Mounting pattern: 25.5*25.5mm φ3mm

Dimensions: 32.5*32.5mm

Weight: 8.5g

ESC // 45A 2-6S

*Current Sensor: Yes

*Input: 2-6S LIPO

*Current scale: 200

*Constant: 45A / Burst: 50A

*BLHeli: BLHeli-S

*RPM-Filter ready: Yes (JazzMaverick or JESC firmware)

*Telemetry: no

*ESC Firmware: BlheliS G-H-30

*Mounting pattern: 25.5*25.5mm/Φ3mm

*Dimensions: 32.5*32.5mm

Important

The DJI Remote Controller is recommended for beginners since you won't need to set up another receiver, but it is also optional in this BNF drone because it is NOT required in order to use the FPV system. If you don't choose to use the DJI Remote Controller, you can choose a receiver option for your transmitter and then bind to your own radio as usual.

Write a Review

Returns Policy
You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.).

You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).

If you need to return an item, simply login to your account, view the order using the "Complete Orders" link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item.

Shipping
We can ship to virtually any address in the world. Note that there are restrictions on some products, and some products cannot be shipped to international destinations.

When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.

Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound.